Description
DC-GSX160301 (Condenser)
The Direct Comfort DC-GSX16 UP TO 16 SEER Central Air Conditioner uses the environmentally friendly refrigerant R-410A and features energy efficiencies and operating sound levels that are among the best in the heating and air conditioning industry. R-410A is chlorine-free to help prevent damage to the ozone layer. The DC-GSX16 features a high-efficiency Copeland® scroll compressor and is designed for the consumer who desires superior comfort, quiet operation, and environmentally friendly air conditioning performance.
Standard Features of this Central Air Conditioner
- R-410A environmentally friendly refrigerant
- High-efficiency Copeland® Ultratech scroll compressor
- Factory-installed filter dryer
- Fully charged for 15 feet of tubing length
- Copper tube/enhanced aluminum fin coil
- Sweat connection service valves with easy access to gauge ports
- Contactor with lug connection
- Ground lug connection
- AHRI Certified
- ETL Listed
The Direct Comfort DC-CAPF Cased Upflow/Downflow Indoor Coils are made for split system air conditioners and heat pumps. The coil’s cabinet is painted Architectural Gray.
Standard Features
- Suitable for use with R-410A and R-22 refrigerants
- Rust-proof, high-temperature, thermoplastic drain pans feature a low water-retention design
- Available with check flowrater expansion device for heat pump or cooling-only applications
- Rifled tubing and corrugated aluminum fin coils
- Foil-faced insulation
DC-GME80805CX (Furnace)
The Direct Comfort DC-GME8 80% AFUE Two-Stage (Convertible), Multi-Speed, Multi-Position Gas Furnace features a super-efficient X13 blower motor that saves electricity during the heating and cooling months. This new direct current motor uses less electricity than the standard multi-speed furnace blower. For example, in constant-fan mode, the X13 runs on an average of 110 watts, whereas a standard furnace multi-speed blower uses an average of 360 watts. This efficiency furnace also includes a patented aluminized-steel tubular heat exchanger and durable Silicon Nitride Hot Surface Ignition system. This Goodman gas furnace is run-tested for heating or combination heating/cooling applications. With a heavy-gauge, reinforced, insulated steel cabinet and durable baked enamel finish, this unit can be installed in a variety of locations.
Standard Furnace Features
- Operates as a natural gas furnace out of the box, and can be easily converted to a propane furnace with optional propane conversion kit.
- X13 blower motor with brushless DC design and a permanent-magnet rotor which allows much more efficient operation furnace in both heating and cooling months
- Patented TuffTube™ dual-diameter tubular furnace heat exchanger with lifetime limited warranty plus 10-year furnace replacement limited warranty (with online registration)
- Heater’s Two-stage gas valve with revolutionary new Dual$aver control technology allows installer to turn on two-stage operation with the flip of a dipswitch
- Goodman Silicon Nitride igniter with patented adaptive learning routine for maximum igniter life
- Integrated furnace electronic furnace control board with self-diagnostics, low-voltage terminal block, and separate terminals for electronic air cleaner and 24-volt humidifiers
- Goodman has furnace control board stores the last five diagnostic codes in memory; simple push-button activation outputs the fault history to a flashing red LED
- Low constant fan mode allows the homeowner to activate the lowest available heating speed to circulate air quietly and efficiently throughout the home during the off cycle
- Furnaces’ self-adjusting feature automatically adjusts furnace to high or low stage based on outsidetemperature without outdoor temperature sensor
- Quiet single-speed, induced-draft blower
- Complies with California NOx emissions standards
Dimensions
Condenser: H36 1/4″ x D29″ x W29″
Furnace: H33 3/8″ x W21″ x D28″
Cased Coil: H30″ x W21″ x D21″